Your local contact in

We are looking forward to your request!

Personal data

Please fill in the mandatory field.

Please fill in the mandatory field.

Please fill in the mandatory field.

Please enter a valid e-mail address.

Please fill in the mandatory field.

Please fill in the mandatory field.

Please fill in the mandatory field.

What topic can we help you with?

Please fill in the mandatory field.

/ 350 Characters

Please note the maximum characters.

* Please fill in the mandadory field

Please accept our data protection.

Unfortunately, your request could not be sent due to a system error. Please try again later.

  • Home
  • Compliance & Data Protection

Compliance and Data Protection

General Information

The protection of personal data is not only an obligation, but rather a matter of concern to us. Any processing of personal data is therefore carried out with the utmost care and in accordance with the fundamental principles of European data protection law. All companies of the ENGEL Group process personal data in compliance with all data protection regulations. In addition to information on data protection at ENGEL, we also provide extensive information about newsletters, website analysis and the integration of third-party services.

All companies of the ENGEL group can be found here.

More detailed information can be found in our information document

Assertion of Your Rights

We are happy to accept your requests to assert your rights under the applicable privacy and dataprotection law (such as information, deletion or revocation).
Click on "Start request" to get to our contact form.

Please direct any other inquiries about data protection to dataprotection@engelglobal.com.

Privacy

Where personal designations are used in this text only in female or male form, they refer to women and men in the same way.

Legal

The author assumes no liability for the quality of the information provided, nor gives any guarantee that the information is up-to-date, correct or complete. Liability claims against the author relating to damages of any kind that were caused by use or misuse of the provided information or by the use of incorrect and incomplete information are excluded, unless there is evidence of willful intent or gross negligence on the part of the author. All offers are non-binding. The author explicitly reserves the right to change, supplement or delete online content in full or in part, or to remove the content temporarily or permanently, without prior notice.

The author accepts no liability for direct or indirect references to third-party Internet pages (links), which are beyond the author's control, unless the author is aware of the content of the linked sites and preventing access of illegal content via these links would have been technically feasible and reasonable. The author therefore explicitly declares that at the time of establishing the links, the corresponding linked pages were free from illegal content. The author has no control whatsoever over the current and future design, and contents of the linked/referenced pages. Therefore, the author hereby specifically distances himself from all contents on linked/referenced sites modified after the links in question were established. This declaration applies to all links and references set within the author's own online content as well as for entries made by third parties in visitor logs, discussion forums, and mailing lists established by the author. Liability for illegal, incorrect or incomplete content, and in particular for damages resulting from use or misuse of such information shall be borne solely by the party providing the linked site and not by the party incorporating the published material published by reference.

In all publications, the author strives to either observe the copyright of the used images, audio and video files, and text, to use their own images, audio and video files, and text or to resort to license-free images, audio and video files, and text. Brands and trademarks mentioned in the author's online content that are protected by third parties are without limitation subject to the terms and conditions of the relevant copyright law, and the right of ownership of the registered owner. Referencing to trademarks does not imply that they are not protected by the rights of a third party. The copyright for any material published and created by the author remains solely with the author. Any reproduction or use of such images, audio and video files, and text in any other electronic or printed publication is not permitted without the author's explicit consent.

This disclaimer is to be considered as part of the online content from which this site was referenced to. If parts or individual formulations of this text should no longer completely correspond to the current legal situation, the other parts remain valid.

Code of Compliance

Key Values of Our Corporate Philosophy

ENGEL offers complete injection molding solutions from a single source. As a leading manufacturer of injection molding machines, we are committed to the innovative development and production of the machines and automation. With innovative technologies, state-of-the-art production facilities and sustainable service and support, we enable our customers to be competitive and successful.

Just as specific quality criteria obviously apply to our machines, clearly defined values apply to our conduct towards customers, suppliers, employees and other business partners.

This Code of Compliance represents fundamental values that apply to the entire ENGEL Group and thereby form the basis for long term, ethically sound, legally compliant business dealings.

We regard this Code not only as a guideline that is binding on our conduct, but also as a key component of our corporate philosophy, and therefore a cornerstone of our continued success in the future.

Download
Code of Conduct
Integrity Helpline

To ensure that the basic principles of this Code of Conduct are sustainably observed in the long term, an Integrity Helpline has been set up. The Helpline, which can be accessed via the digital reporting portal of the Integrity Helpline, is ENGEL’s first port of call for compliance-related enquiries and reports.

Markus Lettau

Sales

+1 (717) 767 2016

Write us

The ENGEL team is happy to support you with extensive knowledge in the field of injection molding.

The browser you are using is outdated.

Internet Explorer is no longer supported. Please switch to an up-to-date browser to use the website to its full extent.

The browser you are using is outdated.

Internet Explorer is no longer supported. Please switch to an up-to-date browser to use the website to its full extent.